ECS News

Automotive electrical work demands patience, knowledge, & above all else, the correct tools. European car owners oftentimes find themselves using ineffective, dangerous, & cumbersome methods when repairing or replacing wiring harness connectors. Schwaben's latest release, the European Car Electrical Terminal Tool Kit, gives enthusiasts the exact tools required for bullet connectors, common ABS sensor and power connectors, trailer light plugs, and more. Extend harness life, ensure proper diagnostic equipment connectivity, and preserve wiring harness life with this superb release.

Your Audi's generator, fans, water pumps and AC compressors all rely on accessory drive belts to do their job. Over time, cracking, glazing, and squeaking occur; for these reasons, replacing your drive belts before they crack or break is a highly prudent investment. Additionally, if the accessory belt snaps constantly, or is sloppy and loose in your vehicle, the only solution is a new tensioner. The ECS-assembled kit comes with everything you need to refresh your whole drive belt system, including the tensioner assembly, accessory belt, and hardware.

The factory Audi B9 A4 transmission mount has a large void in the rubber damping medium, which results in excessive transmission movement under load. This movement results in drivetrain slop than can be observed when accelerating, decelerating, and shifting. This billet aluminum insert is designed to fill the large void in the factory transmission mount, and limit transmission movement without sacrificing ride quality or introducing any additional noise, vibration, or harshness into the cabin.

The belly pans provided for most Audi’s have always appeared to be under-engineered, out of place, cost-cutting parts. Many enthusiasts have even chose to run their vehicles without this protective cover entirely. This decision, however, ignores the unfortunate reality that the belly pan protects several critical engine and drivetrain components. ECS has a much more sensible solution – The Street Shield Skid Plate features corrosion resistant, 4mm thick 5052 aluminum, offering complete engine undercarriage protection.

Maintaining adequate tension on the timing chain is its most basic purpose, keeping the correct level of slack in the chain to best balance noise levels and friction reduction. The second function of this deceptively advanced part is controlling cam timing, maintaining power through all rpms by rapidly adjusting the valve opening and closing event. Assembled By ECS Cam Chain Tensioner kits are available, allowing your 1.8T the opportunity to make maximum power and maintain efficient timing chain operation.

Why would you drill holes into your perfectly good front grille or bumper? Avoid drilling holes by using a tow hook mounted plate bracket from GMG! The No Holes License Plate Bracket does not require you to drill into your bodywork. Instead, it uses a custom-machined stud that screws into the tow hook receptacle. Simply add or remove your license plate without ever damaging your car. Don't Screw It Up - Screw It In.

An unfortunate consequence of the modern closed PCV/breather system is the unintended ingestion of oil vapor and carbon into the intake tract. Thus lowering the octane rating and leaving harmful deposits on a vehicle's intake valves and ports that result in decreased power. Engineered in-house and manufactured here in the USA, the ECS Baffled Oil Catch Can uses a highly efficient 4-chamber oil separator, decreasing oil ingestion and maintaining engine power output. The innovative design also catches as much blow-by gas as possible, bringing carbon buildup to an absolute minimum.

The APR Cast Downpipe Exhaust System replaces the restrictive factory downpipe and chambered resonator with a larger, 76mm stainless steel mandrel-bent system, featuring a bell-mouth cast inlet, high-flow catalyst and various other features. Expect better throttle response, more horsepower and an intoxicating exhaust note while remaining civilized during normal daily driving. It’s one of the best performance enhancements for the 2.0 TFSI following the APR ECU Upgrade. This downpipe was designed and assembled in-house at APR, using premium materials and world-class manufacturing.

An unfortunate consequence of the modern closed PCV/breather system is the unintended ingestion of oil vapor and carbon into the intake tract. Thus lowering the octane rating and leaving harmful deposits on a vehicle's intake valves and ports that result in decreased power. Engineered in-house and manufactured here in the USA, the ECS Baffled Oil Catch Can uses a highly efficient 4-chamber oil separator, decreasing oil ingestion and maintaining engine power output. The innovative design also catches as much blow-by gas as possible, bringing carbon buildup to an absolute minimum.

If you have ever been halfway into a DIY and realized you are missing a specific tool, then you know how frustrating not having the correct tool for the job can be. Even worse is having one that doesn't do the job correctly! Our Schwaben Hand Tools are there to help you finish the job the right way the first time. Don't get caught without the right equipment: save on your Schwaben Hand Tools now with our Partstoberfest Sale!

Normal wear and tear on your engine generates metal particles that will float around in your oil. While this is generally not a symptom of any issues, it can become an issue. Metal flakes in your oil can cause premature wear on internal components and can be an absolute nuisance. Trap those pesky flakes in your drain channel with a Magnetic Drain Plug from ECS and help preserve your engine!

the ECS Billet Aluminum Oil Filter Housing for your Audi or VW will add a touch of class to an ordinary part generally overlooked with durable and attractive convenience. The factory plastic housing can be brittle and is the most appealing part of your engine bay. Give your Audi or VW engine another piece to set it apart from the masses with this aluminum oil filter housing.

Eliminate the visual obstruction of the bright red reflectors on your rear bumper cover with our new Rear Bumper Reflector Film Set. ECS Tuning has collaborated with Lamin-X for a simple and easy-to-install solution to cover the bright red reflectors on the rear bumper cover of B9 A4 vehicles. The Rear Bumper Reflector Film Set includes a pair of pre-cut Gunsmoke Lamin-X film that applies directly over the rear reflectors to tone down the bright red. A great way to give your vehicle a “smoked” appearance. A fantastic addition on either dark or light colored vehicles.

Most aftermarket boost gauges are clearly poorly designed add-ons. The dial numbers and lighting don't match the factory gauges, and most use a mounting system that plainly looks out of place. We think your boost gauge should be easy to see, & match the design of your interior. That's why we've developed a tasteful, center-vent mounted boost gauge kit. The gauge design blends with other dash gauges to give it a classy, factory-installed look. We've even prepared a detailed photo tutorial outlining the installation, so the fun can start as soon as you open the box.

Give your B5 A4 1.8T the clutch it deserves. We've assembled three very special clutch packages built around the ECS Tuning RA4 lightweight flywheel. Mate our new, low mass flywheel to a bigger 240mm clutch. Choose S4, RS4, or Clutch Masters RS4 clutch kits for a smooth, powerful clutch/flywheel package that revs faster but won't forget its manners in traffic. No modifications required. Bolt them on and go, with complete kits that include everything you need, right down to fresh bolts and a clutch alignment tool.

Don't let a tough project stop you in your tracks! Get the right tool for the job with Schwaben Hand Tools from ECS. Tools you can depend on, designed to put the DIY power in your hands, and ready to tackle general and specific jobs, Schwaben Tools are ready to make themselves at home in your garage.

Give your B6 A4 1.8T the clutch it deserves. We've assembled three very special clutch packages built around the ECS Tuning RA4 lightweight flywheel. Mate our new, low mass flywheel to a bigger 240mm clutch. Choose S4, RS4, or Clutch Masters RS4 clutch kits for a smooth, powerful clutch/flywheel package that revs faster but won't forget its manners in traffic. No modifications required. Bolt them on and go, with complete kits that include everything you need, right down to fresh bolts and a clutch alignment tool.

The combustion event inside the cylinder must be carefully controlled to realize maximum power and efficiency. Upgrade to the 2.0T ignition coils to ensure your fuel mixture burns rapidly, thoroughly, and reliably, while enhancing the beauty of your engine bay. The stage I ECS Kit includes everything needed for the conversion: stainless steel hardware and a 2.0T Coil Pack Conversion Plate (3 color options). The stage II Kit adds aluminum Coil Pack Hold Downs (3 color options) to keep pressure on the coil pack—a simple and attractive solution to coils popping out of location.

When the going gets tough sometimes the only tool you want is a good hammer. The Schwaben hammers are built for a lifetime of use from top quality materials. The Ball Peen hammers feature a drop forged steel heads and ergonomic handles giving you accurate striking punches and chisels. The 36-oz Dead Blow hammer is designed with steel shot inside head, delivering a stronger force and at the same time prevents any rebound. For when maximum force is needed with minimal rebound.

Electronically monitored oil level on newer Audi's sounds like a great idea in theory, but what if you want to manually check your oil level? ECS Tuning has recognized this issue and designed our Billet Engine Oil Dipsticks to not only provide you with a more dependable option, but also an attractive addition to your engine bay. 6061-T6 Billet Aluminum handles are finished in two color choices (Polished & Black Anodized), and feature a stainless steel bullet shaped indicator designed to match up with the OEM specified 'Low' and 'Full' oil level marks on the dealership special tool

Electronically monitored oil level on newer Audi's sounds like a great idea in theory, but what if you want to manually check your oil level? ECS Tuning has recognized this issue and designed our Billet Engine Oil Dipsticks to not only provide you with a more dependable option, but also an attractive addition to your engine bay. 6061-T6 Billet Aluminum handles are finished in two color choices (Polished & Black Anodized), and feature a stainless steel bullet shaped indicator designed to match up with the OEM specified 'Low' and 'Full' oil level marks on the dealership special tool.

If you need a replacement turbo to restore the power on your 1.8T, these units from Vaico & Borg Warner will do the trick and a direct bolt-on replacement! With stock size and flow, these turbos are not recommended for modified cars. A completely new, non-rebuild unit that will spool dependably and restore lost performance. Looking for a performance upgrade? We have great options available as well! Borg Warner K04's and FrankenTurbo F21's flow more than stock and allow for higher sustained boost levels! While still being direct bolt-on applications capable of more power!

Audi's double wishbone design provides accurate camber and toe control, handling prowess, and a world-class ride. If it's in shape, that is. Front suspension components are wear parts and must be replaced to insure proper geometry and suspension articulation. If you're tired of noisy suspension bushings and vague steering, take the loud and loose out of your suspension with a new front upper control arm kit and restore that world class ride.

Our new performance transmission mount kit will harness the power of your Audi Engine and Transmission through Advanced Design Methods and Materials. ECS Tuning's Performance Transmission Mount Bushing Insert Kit offers a more engaging driving experience, with crisper throttle response and reduced driveline slop without increasing cabin NVH. The most experienced enthusiasts have learned that an engine that is routinely pushed past the factory-specified stress and flex tolerances requires special accommodations in order to operate consistently at and past the limit.

In most vehicle applications, the corrugated turbo inlet hose found in the intake system is not designed for performance or modification. It was designed to get the job done. When upgrading to a performance filter, intake, or tune the stock inlet hose can start to show it's weakness when suction from the turbocharger is increased. The ECS Silicone Turbo Inlet Hose was designed in-house with a high quality 5-ply construction to provide a strong but flexible structure and secure fit. Includes all necessary clamps for proper installation.

Innovative flywheel options are now available to B8 A4 2.0T owners. The ECS Engineered Lightweight Flywheel weighs in at 17.8lbs VS the factory 26.5lb, a staggering 8.7lbs of weight savings. A decreased mass means a lower moment of inertia, allowing your engine to rev much quicker to help improve acceleration. Our flywheel is heat treated & black zinc plated for corrosion resistance and durability. The ECS option is a model of engineering precision featuring an SFI certification to ensure safe operation. Clutch kits are also available with torque ratings from 320ft/lbs.

The tie rods on your vehicle translate the movement of the steering wheel through the rack and to your wheels. Often, when a vehicle is beginning to experience some higher mileage, the tie rod ends can begin to fail, causing slop in the steering wheel and knocks or creaks in the steering system. Catastrophic tie rod end failure can cause serious damage and danger, as the tie rod end keeps the wheel path straight. Don't allow your outer tie rod ends to fail and ensure safety by replacing your worn or damaged outer tie rod ends.

Add a dose of track inspired carbon fiber to your exterior styling with the ECS Tuning Carbon Fiber Trunk Spoiler. This trunk spoiler was engineered by the masters at ECS to follow the curves and lines of the body which offers a more aggressive look while still matching the factory appeal of your A4. Crafted from 100% high quality, hand laid carbon fiber to achieve it's world class appearance and durability. This spoiler provides a sporty style that's sure to set your vehicle apart from the rest and installs with no drilling, cutting, or modification of any kind!

The tie rods on your vehicle translate the movement of the steering wheel through the rack and to your wheels. Often, when a vehicle is beginning to experience some higher mileage, the tie rod ends can begin to fail, causing slop in the steering wheel and knocks or creaks in the steering system. Catastrophic tie rod end failure can cause serious damage and danger, as the tie rod end keeps the wheel path straight. Don't allow your outer tie rod ends to fail and ensure safety by replacing your worn or damaged outer tie rod ends.

An elegant solution to vague and imprecise steering, performance control arms with poly bushings let you feel the road through your fingertips. Factory rubber bushings are intended to buffer road sensations from steering input. But for the performance driver, a highly tactile connection to the road conveys more information about vehicle dynamics, sharpening driving awareness. That's why we're offering control arm assemblies already fitted with poly bushings that tighten suspension feel, restore vehicle safety, and last many miles longer than stock bushings. Stay in control.