Installation of this kit is now easier than ever, without the need of removing the crash bar to drill holes for bracket mounting.
Installation of this kit is now easier than ever, without the need of removing the crash bar to drill holes for bracket mounting.
Remove the final power restriction on your 3.0T with an over 20% higher flowing throttle body, fully releasing the complete power potential from your factory supercharger.
* Existing IE Dual Pulley Upgrade Required *
*The included IE air intake inlet will require custom adapter work to fit your stock or aftermarket intake - NOT A DIRECT INSTALL*
Increase supercharger rotational speed to provide more boost to your engine
2X Entries Into Our F80 M3 Sweepstakes
*Stage 2 software required after install. See ES4266021
Reduce restrictions and increase cooling! Whether you call it an intercooler, a heat exchanger, a radiator, or something else - this is the product for you.
10X Entries Into Our F80 M3 Sweepstakes
For vehicles from the 2016 model year (Facelift)
This product was last offered at the strikethrough price on
06-13-2026
Easily increase the supercharger rotational speed to create more boost
10X Entries Into Our F80 M3 Sweepstakes
Late 3.0T Bolt On Pulley - Please Confirm Fitment Before Ordering - Appropriate stage 2 software is requi
This product was last offered at the strikethrough price on
06-13-2026
Dramatically increase horsepower and torque by increasing the rotational speed of the factory supercharger (Press-On SC Pulley)
Call In Or Chat For Best Price!
Stage II software is required to run any upgraded Pulley configuration and is sold separately - Please se
*For models with press-on style supercharger pulley (3.0T gen1 / Simos 8.x ECU)*
This product was last offered at the strikethrough price on
09-28-2026
Unleash the true potential of your supercharger!
10X Entries Into Our F80 M3 Sweepstakes
Only for pre-facelift vehicles with press on supercharger pulley
This product was last offered at the strikethrough price on
06-13-2026
Increases supercharger RPM by 26% when paired with IE 57.5mm overdrive supercharger pulley
Requires 57.5mm SC pulley and stage 2 dual pulley ECU tune
Eliminates the problematic two-piece design and rubber isolator found in the stock crank pulley while reducing the mass of the motor's rotating assembly.
*To be used with 'Stage 2' software or software specific to a supercharger crank pulley upgrade*
Larger diameter pulley increases the speed at which the supercharger spins, increasing the boost pressure output
*NOTE: This kit must be used with appropriate "Stage 2" performance software.
This product was last offered at the strikethrough price on
09-29-2026
Larger diameter pulley increases the speed at which the supercharger spins, increasing the boost pressure output
Most Stage 2+ software tunes are compatible with this kit. Be sure to use the correct software for 192mm
This product was last offered at the strikethrough price on
09-29-2026
Our Red Kevlar accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt.
10X Entries Into Our F80 M3 Sweepstakes
Our Red Kevlar accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt.
10X Entries Into Our F80 M3 Sweepstakes
For use with 187.3mm crank pulley & 57.6mm supercharger pulley only
This product was last offered at the strikethrough price on
10-14-2026
Seals the inner ends of the intercoolers to the front of the supercharger compressor
Replace those failure prone, plastic 3.0 TFSI supercharger bleeder screws with the 034Motorsport 3.0 TFSI Supercharger Bleeder Screw Kit!
2X Entries Into Our F80 M3 Sweepstakes
Everything needed to replace failed heat exchangers.
10X Entries Into Our F80 M3 Sweepstakes
For vehicles from 2015+
This product was last offered at the strikethrough price on
08-24-2026